Chevelle Tech - View Profile: UMI Performance

UMI Performance UMI Performance is offline

  Visitor Messages

Showing Visitor Messages 1 to 6 of 6
  1. Pats70ss
    Dec 20th, 17 1:54 PM - permalink
    Pats70ss
    Hey Guys,


    My 70 Chevelle is slowing becoming a complete UMI machine I thnk I am getting close to having pretty every piece you guys offer on there. Question about the rear coil over kits. Good ? bad? I put the UMI fixed shocks on last fall. Put the Viking DA's on the front (craig did some adjusting on them at Carlisle for me) Thinking about switching to coil over in the rear to have everything match up. Any cons to doing this?


    Pat
  2. DanG
    Mar 17th, 16 3:48 PM - permalink
    DanG
    Do you guys give any discounts for T/C members?
  3. WurlitzBurg
    Sep 12th, 14 3:45 PM - permalink
    WurlitzBurg
    Ryan,
    Can you tell me the length between mounting surfaces of your sway bar for '69 chevelle? I want to make sure they fit ok. After a restoration you never know what you will have. Thanks,
    Tom
  4. mark157
    Dec 22nd, 13 10:49 AM - permalink
    mark157
    What would you recommend for wheel hop ,I just installed one of Mark Jones 468 bbc from this site and I already know I have wheel hop from just driving around shop. I have all new suspension with boxed factory lower control arms,I'm looking at upper adjustable arms and the reinforcements, what would you suggest to stop or reduce wheel hop. Thanks Mark
  5. UMI Performance
    Jan 14th, 09 11:01 AM - permalink
    UMI Performance
    Bill,

    I just sent over the installation instructions via e-mail. Right now we do not have any sales planned but maybe I can work one out. We also have our frame supports under design now.

    Hope that helps!
    Ryan
  6. Bilster
    Jan 14th, 09 10:46 AM - permalink
    Bilster
    Ryan,
    Thanks for your generous offer for instructions on the installation of Energy Suspension bushings. Could you please send them to [email protected]? Also, are there any plans for a group purchase of UMI rear lower control arms or the attached frame stabilizers?
    Bill

  About Me

  Statistics

Total Posts
Visitor Messages
General Information
  • Last Activity: Yesterday 9:03 AM
  • Join Date: Jul 2nd, 05
  • Referrals: 0

  Mentions

No results to display...

  Quotes

Nov 8th, 18
2:30 PM - UMI Performance quoted HairBandDan in post Re: UMI suspension concerns
Hi Guys i know this is a older t...
May 15th, 18
9:00 AM - UMI Performance quoted -SS454- in post Re: Currie Currectrac UCA's don't adjust short enough?
what is a rod end UCA? Li...
May 14th, 18
5:54 PM - -SS454- quoted UMI Performance in post Re: Currie Currectrac UCA's don't adjust short enough?
The UMI uppers with Roto-joints go 3...
Mar 28th, 18
1:41 PM - reek quoted UMI Performance in post Re: 1967 rear coil spring
As mentioned 66 is different than 67...
1:11 PM - 99airwarrior quoted UMI Performance in post Re: UMI Rear Coilover kit
A coilover allows the ability to adj...
8:34 AM - UMI Performance quoted 99airwarrior in post Re: UMI Rear Coilover kit
What are the benefits of rear coi...
Mar 27th, 18
8:47 AM - UMI Performance quoted NW68SSBBC in post Re: Rear Sway bar for Quick Performance Ford 9"
I'm a pretty fair welder/fabri...
Mar 26th, 18
6:53 PM - NW68SSBBC quoted UMI Performance in post Re: Rear Sway bar for Quick Performance Ford 9"
For back bracing you would need to d...
5:59 PM - UMI Performance quoted HKalin in post Re: Anyone Have This Paticular Driveshaft Loop
3/4" all around. Whoops....
5:30 PM - HKalin quoted UMI Performance in post Re: Anyone Have This Paticular Driveshaft Loop
Hello All, Yes that is correct, ...
8:50 AM - UMI Performance quoted NW68SSBBC in post Re: Rear Sway bar for Quick Performance Ford 9"
I see where they offer their b...
Mar 20th, 18
9:58 PM - NW68SSBBC quoted UMI Performance in post Re: Rear Sway bar for Quick Performance Ford 9"
Hey Joe, If you go with a chassis mo...
9:55 AM - UMI Performance quoted NW68SSBBC in post Re: Rear Sway bar for Quick Performance Ford 9"
Hello, does anyone know who ma...
Feb 26th, 18
8:48 AM - UMI Performance quoted thebeast in post Re: Front end alignment
Thanx, Ryan ..... The car (39...
Feb 24th, 18
1:30 PM - thebeast quoted UMI Performance in post Re: Front end alignment
Hey Kurt, Our Stage 1 kit overs ...
12:14 PM - UMI Performance quoted thebeast in post Re: Front end alignment
Anyone installed a UMI Stage ...
Feb 14th, 18
8:46 AM - Chevelle396BB quoted UMI Performance in post Re: 1968 Chevelle - 2017 Build/Project
Awesome to hear! If you have any...
Feb 10th, 18
9:38 AM - starnester quoted UMI Performance in post Deleted Posts
Feb 7th, 18
10:14 PM - Pete 67 quoted UMI Performance in post Re: Chevy A body - tall spindle vs tall ball joint
We also carry and have the tall 2" d...
Jan 17th, 18
11:06 AM - lucifershammer quoted UMI Performance in post Re: Differential Housing Roto-joints...
On the rear end housing "ears" we ha...
For the best viewing experience please update your browser to Google Chrome